Avondale Pot Rack with Venetian Glass Shades

Assembly and Installation Instructions

Kalco Customer Service: (702) 361 4345, (800) 525 2655, www.kalco.com Installation Sheet for Heavy Fixtures (50 lbs and Over) Caution: Turn off electricity at main fuse box before installation. If you are not familiar with electrical wiring, have a qualified electrician make this installation. Risk of fire: Do not use lamps with greater wattage than is labeled on this fixture. Method A: (Brace is directly on top of the outlet box and not accessible) Using a 1/8 drill bit, pre-drill (4) holes into the wood brace through the (4) hole pattern in the outlet box. (Outlet box is shown as a cutaway for clarity). Secure the hickey to the brace with (4) #8 x 1-1/2 screws. The wire way opening should mount between the outlet box 2 mounting flanges. Method B: (Brace is on top and not in contact with the outlet box and is accessible) Remove center knockout from outlet box. In line with the center knockout, drill a 9/16 hole in the brace. (Brace should be fastened to the ceiling joist after pipe is installed). Assemble hickey to one end of a ﾼ pipe/nipple. The pipe should be flush with the inside of the hickey wire way. Insert pipe through back of outlet box and through the brace above. Secure pipe with a ﾼ pipe cap nut. After following method A or B: 1. Thread nut onto the nipple and fasten nipple with a lockwasher into the hickey so the nipple is flush with the inside of the hickey wire way. Tighten hex nut against the hickey. Fasten the loop and chain assembly to nipple. Loop should be approximately 7/8 below ceiling line. 2. Determine the length of chain you need and remove or add chain links at this time. Feed canopy followed by loop ring nut up the chain and connect chain to fixture loop with open link (provided) and close the link. Cover link with cloth to protect finish. 3. Lace fixture wire, ground wire and safety cable through chain links and through loop. Pull all wires out of the hickey wire way with needle nose pliers. Trim off excess wires and cable. Leave approximately 6 out from hickey. Strip 5 of plastic cover from the end of the safety cable. Loop cable back around hickey and through wire way. Pass end of cable through cable clamp. Loop cable back through cable clamp and secure clamp on cable tightly. 4. Splice the ribbed side of the parallel wire to the white supply wire from the outlet box with wire connector (not supplied). Splice the smooth side of the parallel wire to the black supply wire from outlet box with wire connector. Splice ground wires with wire connector. Push all wires into the outlet box. 5. Raise canopy to cover outlet box and secure in place with ring nut. Add any glass or shades. Kalco Mounting and Wiring Instructions for Pot Rack Fixtures Caution: 1. This fixture has the potential of weighing more than 50 lbs. therefore it must be installed independent of the outlet box. 2. Turn off electricity at the main fuse box before installation. 3. Risk of fire: Do not lamp fixture greater than wattage shown on maximum wattage labels where attached. Step 1: This fixture may have other instruction sheets; refer to them for the complete assembly of this fixture. Step 2: To mount independent of the outlet box the outlet box must be secured to a brace above the outlet box. Step 3: Fasten the cast hickey through the outlet box and into the brace with (4) #8 x 1-1/2 long screws. Pre-drill holes into brace with a 1/8 diameter drill bit. Step 4: Thread the nipple into the hickey so it is below the ceiling level 1-1/2. Secure nipple with lockwasher and hex nut. Step 5: Determine the length of chain you need for your fixture height and add or remove links. Thread fixture wire/ground wire through the chain links and through the loop(s) on the canopy. Step 6: Splice the ribbed side of the parallel wire to the white supply wire from the outlet box with wire connector (not supplied). Splice the smooth side of the parallel wire to the black supply wire from the outlet box with wire connector. Splice ground wires with wire connector. Step 7: Push all wires into the outlet box and raise canopy over the nipple and secure tightly with cap nut. Add lamps and other accessories. Turn on accessory. '